Electronic Fume Extraction Solutions for Power Electronics
Industry:

Key Highlights
- Fume capture for power electronics assembly: heavy-joint soldering, busbar and terminal welding, brazing, potting and coating
- Extraction scaled to heavier fume loads, from single soldering benches to laser welding cells at 1150 m³/hr
- Pre-filter, HEPA and activated carbon filtration for flux smoke, metal fume and resin vapours
- Mobile extraction on castors for brazing, repair and maintenance work around large assemblies
- Supplied and supported in India by USI, authorised distributor of Donaldson BOFA, with busbar laser welding from Lava X
Why Power Electronics Assembly Produces Heavier Fumes
Inverters, converters, chargers, motor drives and power modules carry far more current than signal electronics, and that shows on the assembly floor. Heavy copper boards and large terminals need more heat and more flux to solder, busbars and cell connectors are welded rather than soldered, and potting compounds and conformal coatings are applied in thicker layers to protect against heat and moisture.
Each of these steps releases more fume than a typical PCB rework bench: denser flux smoke from large joints, fine metal fume from copper and aluminium welding, and resin vapours from potting and coating. The operators doing this work stand close to the source, and the residue can settle on the cooling surfaces and connections that a power module depends on.
Electronic Fume Extraction for Power Modules and Busbars
Electronic fume extraction captures the fume at the soldering tip, welding head or dispensing nozzle and filters it before the air returns to the room. In power electronics the extractor has to cope with a higher and more varied load than at a light soldering bench, so airflow, pre-filter capacity and gas filtration all need to be sized up.
The result is a mix of units: robust bench extractors at soldering stations, a laser fume extractor on each welding cell, and a mobile unit that can follow brazing and repair work to wherever the assembly is.
Why Fume Load and Fume Type Decide the Extractor
Power electronics lines combine three very different fume sources, and each one sets different demands:
- Heavy-joint soldering: large terminals and heavy copper need more flux, so the HEPA and carbon filters load faster and benefit from continuous-duty bench units.
- Busbar and terminal welding: laser welding of copper and aluminium produces fine metal fume, which needs high airflow and a large pre-filter to avoid frequent filter changes.
- Potting, coating and adhesives: resin and solvent vapours pass straight through particle filters, so an activated carbon stage is essential.
Built for Inverter, Charger and Power Module Lines
The equipment covers the bench, the welding cell and the work that moves around large assemblies.
Continuous soldering at the bench
The T 15 is a single-operator extractor for continuous soldering, with HEPA and carbon filters, a replacement indicator and noise below 56 dBA.
Welding copper and aluminium busbars
The Lava X LAVACELL battery pack laser welding machine joins copper and aluminium busbars, tabs and terminals, including Cu-Al joints, with vision positioning and melt pool monitoring.
High airflow for welding cells
The AD 1500 iQ delivers 1150 m³/hr with HEPA and carbon filtration and iQ tracking of airflow and filter condition, for laser welding and other heavy fume loads.
Extraction that moves with the job
The Mobile FumeKART rolls on castors to brazing, repair and maintenance work, with an adjustable arm and HEPA and carbon filtration at 380 m³/hr.
Building a Complete Power Electronics Extraction Setup
Soldering of terminals, heavy copper boards and power module connections is covered at each bench by the T 15. Busbars, tabs and terminals are joined on the Battery Pack Laser Welding Machine, and the metal fume from that cell is captured by the AD 1500 iQ. Brazing, repair and touch-up work around large inverter and charger assemblies is handled by the Mobile FumeKART, and genuine BOFA replacement filters for every unit are supplied from India.
Who Uses It
- Inverter, converter and motor drive manufacturers
- EV charger, on-board charger and battery management system makers
- Power module and IGBT assembly lines
- Solar inverter and energy storage system producers
- Transformer, UPS and industrial power supply manufacturers
Supply and Support in India
United Spectrum Instruments (USI), Chennai, is the authorised distributor of Donaldson BOFA in India and supplies electronic fume extraction units, laser fume extractors, mobile extractors and replacement filters for power electronics manufacturing, together with Lava X laser welding machines for busbars and terminals.
USI helps match each soldering bench, welding cell and work area to the right extractor and filter set, and provides help with sizing, set-up and filter changes by phone, WhatsApp and video call.
Request a Configuration
Download the brochure from this page, use the Enquire Now button, write to sales@unitedspectrum.in, or call +91 93631 83748 / +91 97899 04948. Please mention:
- The processes to be covered: soldering, laser welding, brazing, potting or coating
- The number of benches and welding cells, and whether mobile extraction is needed
- The materials and consumables in use: flux, busbar metals, potting compounds and coatings
- Your shift pattern, and any existing BOFA units or ducting
GET IN TOUCH WITH US
Have a Project in Mind ? Let’s Talk
FAQs
Why is fume extraction needed in power electronics manufacturing?
Power electronics assembly uses heavy-joint soldering, busbar and terminal welding, brazing, potting and coating, which together release more fume than signal electronics work. Flux smoke, fine metal fume and resin vapours collect close to the operator and can settle on cooling surfaces and connections. Capturing them at each bench and cell protects operators and keeps power modules clean.
What fumes come from power electronics assembly?
There are three main types. Soldering of large terminals and heavy copper gives off dense flux smoke. Laser welding of copper and aluminium busbars, tabs and terminals produces fine metal fume. Potting compounds, conformal coatings and adhesives release resin and solvent vapours. Electronic fume extraction for power electronics therefore needs HEPA filtration for particles and activated carbon for vapours.
Which extractor suits busbar and terminal welding?
Laser welding of busbars and terminals creates a steady load of fine metal fume, so it needs a laser fume extractor with high airflow and a large pre-filter. The AD 1500 iQ delivers 1150 m³/hr with HEPA and carbon filtration and iQ monitoring of filter condition. For brazing and repair around large assemblies, the Mobile FumeKART follows the work on castors.
Who supplies electronic fume extraction for power electronics in India?
United Spectrum Instruments (USI), Chennai, is the authorised distributor of Donaldson BOFA in India. USI supplies bench, laser and mobile fume extractors with genuine replacement filters to inverter, charger, power module and energy storage manufacturers, and can also supply Lava X laser welding machines for busbars and terminals, with sizing guidance and remote technical support.
How do I get a quote or datasheet for power electronics fume extraction?
Download the brochure from this page or click Enquire Now. You can also email sales@unitedspectrum.in or call +91 93631 83748 / +91 97899 04948. For an accurate quote, mention the processes to be covered, the number of benches and welding cells, the flux, busbar metals, potting compounds and coatings in use, your shift pattern and any existing BOFA units.
